IN1608 Series |
|
Video input |
Number/signal type |
2 RGB, RGBcvS, component video (YUVi or YUVp/HDTV), S-video, composite video 4 HDMI digital video (HDCP compliant) 2 DTP 230 (HDCP compliant) |
Connectors |
2 female 15-pin HD 4 female HDMI type A 2 female RJ-45 connectors |
Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
Minimum/maximum levels |
Analog: 0.0 V to 1.0 Vp-p with no offset at unity gain |
Impedance |
75 ohms |
Horizontal frequency |
15 kHz to 100 kHz |
Vertical frequency |
24 Hz to 120 Hz |
Resolution range |
640x480 to 1600x1200 and 1920x1200* NTSC, PAL, SECAM, 480i, 480p, 576i, 576p, 720p, 1080i, 1080p, and 2k *reduced blanking |
Return loss |
>30 dB @ 5 MHz |
DC offset (max. allowable) |
1.5 V |
|
Video processing |
Decoder |
12 bit digital (3D-adaptive comb filter) |
Analog sampling |
12 bits per color; 13.5 MHz standard (video) 170 MHz standard (RGB) |
Digital pixel data bit depth |
8, 10, or 12 bits per channel; 165 MHz pixel clock (HDMI) |
Colors |
1 billion (10 bit processing) |
|
Video output |
Number/signal type |
2 HDMI digital video (HDCP compliant) 1 DTP 230 (HDCP compliant) |
Connectors |
2 female HDMI 1 female RJ-45 connector |
Scaled resolution |
640x4806,8,9, 800x6006,8,9, 852x4806,8,9, 1024x7686,8,9, 1024x8526,8,9, 1024x10246,8,9,1280x7686,8,9, 1280x8006,8,9, 1280x10246,8,9, 1360x7656,8,9, 1360x7686,8,9, 1365x7686,8,9, 1365x10246,8,9, 1366x7686,8,9,1400x10506,8, 1440x9006,8,9, 1600x9006,8, 1600x12006,8, 1680x10506,8, 1920x12006,8 HDTV 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8 1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz,4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz, 9 = at 75 Hz |
|
Sync |
Input type |
RGBHV, RGBS, RGsB, RGBcvS, bi-level or tri-level component video |
Input standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level |
2.75 V to 5.0 Vp-p for RGBHV or RGBS 0.6 Vp-p for component video with tri-level sync 0.3 Vp-p for component video with bi-level sync or RGsB |
Input impedance |
Horizontal: 510 ohms Vertical: 510 ohms |
Max. input voltage |
5.0 Vp-p |
|
Audio |
Gain |
Unbalanced output: -6 dB; balanced output: 0 dB |
Frequency response |
20 Hz to 20k Hz, ¡¾0.5 dB |
THD + Noise |
<0.1%, 20 Hz to 20k Hz at nominal level |
S/N |
>90 dB at maximum balanced output (unweighted) |
Crosstalk |
¡Â-80 dB @ 1 kHz, fully loaded |
Stereo channel separation |
>80 dB @ 1 kHz |
Bass |
+12 dB to -24 dB @ 100 Hz |
Treble |
+12 dB to -24 dB @ 8 kHz |
|
Audio input |
Number/signal type |
8 stereo line level balanced or unbalanced 2 mono mic/line level balanced or unbalanced (with available phantom power) 4 stereo, de-embedded from HDMI (PCM only) 2 DTP 230 (de-embedded from HDMI [PCM only], or remote balanced/unbalanced analog) |
Connectors |
(6) 3.5 mm captive screw connectors, 5 pole for line (2) 3.5 mm captive screw connectors, 3 pole for mic/line 4 female HDMI type A 2 female RJ-45 connectors |
Impedance |
>10k ohms unbalanced, >20k ohms balanced |
Nominal level |
Line inputs: +4 dBu, -10 dBV, adjustable Mic/line inputs: -60 dBV, +4 dBu, -10 dBV, adjustable |
Maximum level |
Line inputs: +21 dBu balanced, +15 dBu unbalanced Mic/line inputs: +12 dBV (2 Vrms) when gain is set to 0 dB |
CMRR |
>80 dB @ 1 kHz |
Input gain adjustment |
Line inputs: -18 dB to +24 dB, 1 dB steps, adjustable per input Mic/line inputs: -18 dB to +60 dB, 1 dB steps, adjustable per input |
NOTE |
Unbalanced analog inputs applied at a DTP Tx input have +12 dB of gain applied to bring the signal to a nominal level for balanced operation. | |
DC phantom power |
+48 VDC ¡¾10% (can be switched on or off per mic/line input) |
|
Audio output |
Number/signal type |
1 balanced or unbalanced stereo (variable) 1 balanced or unbalanced stereo; can be configured as stereo or two independently mixed mono channels 2 HDMI embedded 1 DTP 230 (embedded digital, and remote balanced/unbalanced analog) |
Connectors |
(2) 3.5 mm captive screw connectors, 5 pole 2 female HDMI 1 RJ-45 connector |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
¡¾0.5 dB channel to channel |
Maximum level (Hi-Z) |
>+12 dBu, balanced; >+6 dBu, unbalanced |
Output volume range |
0 to -100 dB in 1 dB steps |
NOTE |
System gain for the analog DTP Rx output is rated at -12 dB (unbalanced) and -6 dB (balanced). | |
|
Audio output — power amplifier (MA/SA models only) |
Number/signal type |
|
IN1608 SA |
1 stereo (default) or 2 mono (2 channels total) |
IN1608 MA |
1 mono, 70 V line |
Connectors |
|
NOTE |
This connector accepts wires of 22 AWG to 12 AWG. | |
IN1608 SA |
(1) 5 mm screw lock captive screw connector, 4 pole |
IN1608 MA |
(1) 5 mm screw lock captive screw connector, 2 pole |
Load impedance |
|
IN1608 SA |
4 ohms minimum |
IN1608 MA |
50 ohms minimum |
Amplifier type |
Class D |
Output power |
|
IN1608 SA |
25 watts per channel, 8 ohms, 1 kHz, 0.1% THD 50 watts per channel, 4 ohms, 1 kHz, 0.1% THD |
IN1608 MA |
100 watts (rms) @ 70 V, 1 kHz, 0.1% THD |
Protection |
Clip limiting, thermal, short circuit, DC output |
Frequency response |
20 Hz to 20 kHz, -3 dB to +1 dB @ 1 W |
THD + Noise |
<0.1% @ 1 kHz, 3 dB below clipping |
S/N |
>90 dB, 20 Hz to 20 kHz, unweighted |
|
Control/remote |
Serial control port |
1 bidirectional RS-232, 3.5 mm captive screw connector, 3 pole (rear panel) |
Baud rate and protocol |
9600, 8 data bits, 1 stop bit, no parity (default) |
Serial control pin configuration |
1 = Tx, 2 = Rx, 3 = GND |
USB control port |
1 front panel female mini USB B |
USB standards |
USB 2.0, high speed |
Ethernet control port |
1 female RJ-45 connector |
Ethernet data rate |
10/100Base-T, half/full duplex with autodetect |
Ethernet protocol |
ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet |
Program control |
Extron control/configuration program for Windows¢ç Extron Simple Instruction Set (SIS¢â) Microsoft¢ç Internet Explorer¢ç, Telnet |
|
Control/remote — external device (pass-through, unidirectional or bidirectional) (RS-232/IR over DTP) |
NOTE |
Protocol is mirrored between the connected DTP 230 endpoints and the "Over DTP" ports on the IN1608. Signals from a control device pass into each IN1608 "Over DTP" port, are embedded with the DTP signal, and sent to individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over DTP" ports are simply pass-through connections to DTP endpoints. There is no RS-232 or IR insertion from any IN1608 control port to the "Over DTP" ports. | |
Serial control pass-through ports |
|
IN1608 input/DTP Tx |
RS-232 via (2) 3.5 mm, 5 pole captive screw connectors (shared with IR ports) |
IN1608 output/DTP Rx |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector (shared with IR port) |
Baud rates |
300 to 38400 baud |
Protocol |
8 or 7 data bits 1 or 2 stop bits no parity (default) even or odd parity |
Serial control pin configuration |
1 = Tx, 2 = Rx, 3 = GND |
IR pass-through control ports |
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
IN1608 input/DTP Tx |
(2) 3.5 mm captive screw connectors, 5 pole (shared with RS-232 ports) |
IN1608 output/DTP Rx |
(1) 3.5 mm captive screw connector, 5 pole (shared with RS-232 port) |
IR control pin configuration |
3 = GND, 4 = IR Tx, 5 = IR Rx |
|
General |
Power supply |
Internal Input: 100-240 VAC, 50-60 Hz |
Power consumption |
|
IN1608 |
45 watts |
IN1608 SA, IN1608 MA |
Amp at 1/8 power: 66 watts |
Remote power capability |
Supports up to three endpoints (two DTP Tx, one DTP Rx) |
Temperature/humidity |
Storage: -40 to +158 ¡ÆF (-40 to +70 ¡ÆC) / 10% to 90%, noncondensing Operating: +32 to +122 ¡ÆF (0 to +50 ¡ÆC) / 10% to 90%, noncondensing |
Cooling |
Fans, right to left (as viewed from front panel) |
Thermal dissipation |
|
IN1608 |
85 BTU/hr |
IN1608 SA, IN1608 MA |
Amp at 1/8 power: 120 BTU/hr |
Mounting |
|
Rack mount |
Yes, with included, pre-installed brackets |
Enclosure type |
Metal |
Enclosure dimensions |
|
IN1608 |
1.75" H x 17.5" W x 9.5" D (1U high, full rack wide) (4.4 cm H x 44.4 cm W x 24.2 cm D) (Depth excludes connectors and knobs. Width excludes rack ears.) |
IN1608 SA, IN1608 MA |
3.5" H x 17.5" W x 9.5" D (2U high, full rack wide) (8.1 cm H x 44.4 cm W x 24.2 cm D) (Depth excludes connectors and knobs. Width excludes rack ears.) |
Product weight |
|
IN1608 |
5.0 lbs (2.3 kg) |
IN1608 SA, IN1608 MA |
7.4 lbs (3.4 kg) |
Shipping weight |
|
IN1608 |
7 lbs (4 kg) |
IN1608 SA, IN1608 MA |
11 lbs (5 kg) |
DIM weight |
|
IN1608 |
8 lbs (4 kg) |
IN1608 SA, IN1608 MA |
22 lbs (10 kg) |
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
Environmental |
Complies with the appropriate requirements of RoHS, WEEE. |
Warranty |
3 years parts and labor
|