| MTP/HDMI U R |
|
| Video |
| MTP input |
|
| Gain |
Unity |
| Maximum resolution |
|
| Analog |
Up to 2048x1080 or 1080p @ 60 Hz |
| Signal transmission distance, analog |
 |
| HDMI digital input |
|
| Maximum data rate |
4.95 Gbps (1.65 Gbps per color) |
| Maximum pixel clock |
165 MHz |
| Maximum resolution |
|
| Digital |
Up to 1920x1200 or 1080p @ 60 Hz |
| Signal transmission distance, digital |
 |
| NOTE |
The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system. | |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI 1.2 |
|
| Video input |
| Number/signal type |
|
| MTP input |
1 set of proprietary analog signals |
| HDMI digital input |
1 set of proprietary digital signals |
| Connectors |
|
| MTP input |
1 female RJ-45 |
| HDMI digital input |
2 female RJ-45 |
|
| Video output |
| Number/signal type |
|
| Analog output |
1 RGBHV, RGBS, component video (bi-level and tri-level), S-video, composite video (follows input type) |
| HDMI digital output |
1 single link HDMI (or DVI-D*) |
| Connectors |
|
| Analog output |
1 female 15-pin HD for RGB
3 female BNC for Y, R-Y, B-Y
1 female 4-pin mini DIN for S-video (Y/C)
1 female BNC for composite video |
| HDMI digital output |
1 female HDMI type A |
| Nominal levels |
Analog outputs:
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels |
Analog outputs: 0.8 V to 1.2 Vp-p |
| Impedance |
Analog outputs: 75 ohms (during video output only) |
| Return loss |
Analog outputs: <-30 dB @ 5 MHz (during video output only) |
| DC offset |
Analog outputs: <±20 mV with input at 0 offset |
|
| Sync — analog outputs |
| Output type |
RGBHV, RGBS, component video (bi- or tri-level) |
| Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Output level |
4.0 V to 5.0 Vp-p, unterminated |
| Output impedance |
87 ohms (24 mA) |
| Polarity |
Positive or negative (selectable) |
|
| Audio — from MTP input |
| Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response |
20 Hz to 20 kHz, ±1 dB |
| THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N |
>70 dB at maximum output (unweighted) |
|
| Audio input — from MTP input, see MTP transmitter's audio output specifications |
| Number/signal type |
1 set of proprietary analog signals |
| Connectors |
1 female RJ-45 |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu | |
|
| Audio output — from MTP input |
| Number/signal type |
2 mono, balanced/unbalanced |
| Connectors |
(1) 3.5 mm captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain error |
±1 dB channel to channel |
|
| Control/remote — external device (pass-through) from the HDMI input |
| Serial control port input/output |
RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
| Serial control pin configuration |
Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND |
|
| Control/remote — external device (pass-through, unidirectional or bidirectional) from the MTP input |
| Serial control port input/output |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector (3 poles are used) |
| Baud rates |
Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible.
Performance varies based on baud rate and cable length.) |
|
| General |
| Recommended cable type |
Shielded or unshielded |
| MTP input |
CAT 5/5e/6 |
| HDMI digital input |
CAT 5/5e/6, Extron DTP26 |
| External power supply |
100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
| Power input requirements |
12 VDC, 0.8 A |
| Cooling |
Convection, no vents |
| Thermal dissipation |
|
| 115 VAC, 60 Hz |
16.7 BTU/hr |
| 240 VAC, 50 Hz |
18.1 BTU/hr |
| Mounting |
| Rack mount |
Yes, with optional 1U rack shelf |
| Furniture mount |
Yes, with optional under-desk mounting kit |
| Pole mount |
Yes, with optional projector mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.7" H x 8.75" W x 3.0" D (half rack wide)
(4.3 cm H x 22.2 cm W x 7.6 cm D)
(Depth excludes connectors.) |
| Product weight |
0.8 lbs (0.4 kg) |
| Shipping weight |
2 lbs (1 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, UL
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply. |
| EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor |
