DCX 1600 Series |
|
Video — DCX DVI Pro Boards |
NOTE |
*Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. | |
Routing |
4 x 4 to 16 x 16 matrix, expandable by increments of 4 inputs and 4 outputs |
Gain |
Unity |
Resolution range |
Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single link DVI standard) @ 60 Hz |
Signal type |
Single-link DVI digital video signals are supported. |
NOTE |
The DCX 1600 DVI Pro Series boards are compatible with HDMI 1.3. | |
Digital audio |
Supports HDMI audio (if using an HDMI to DVI adapter) transmitted through the RGB and Y, Cr, Cb lines, actively buffered. |
Consumer Electronics Control (CEC) |
Supports CEC wired infrared data pass-through using the HDMI 1.3 standard. |
EDID and DDC |
Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
HDCP |
Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards |
HPD |
Supports hot plug detection (HPD) of display as a pass-through signal. |
Maximum data rate |
6.75 Gbps (2.25 Gbps per color) |
Maximum pixel clock |
225 MHz |
Standards |
DVI 1.0, HDMI 1.3 |
|
Video input — DCX DVI Pro input boards |
Number/signal type |
4 digital RGB single link DVI-D (or HDMI*) per input board |
Connectors |
4 female DVI-I (digital only) per input board |
Equalization |
Automatic |
Input cable length |
>50' (15.24 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p |
NOTE |
The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. | |
|
Video output — DCX DVI Pro output boards |
Number/signal type |
4 digital RGB single link DVI-D (or HDMI*) per output board |
Connectors |
4 female DVI-I (digital only) per output board |
Re-clocking |
Automatic |
Peripheral device power |
250 mA per output |
|
Video — DCX HDMI boards |
NOTE |
*Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. | |
Routing |
4 x 4 to 16 x 16 matrix, expandable by increments of 4 inputs and 4 outputs |
Gain |
Unity |
Resolution range |
Up to 1920x1200 or 1080p @ 60 Hz |
Signal type |
Single-link HDMI (or DVI-D*) |
Digital video |
RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to 1600x1200 @ 60 Hz computer video) |
NOTE |
These DCX HDMI Series boards are compatible with HDMI 1.3. | |
Digital audio |
Supports HDMI audio transmitted through the RGB and Y, Cr, Cb lines, actively buffered. |
Consumer Electronics Control (CEC) |
Supports CEC wired infrared data pass-through using the HDMI 1.3 standard. |
EDID and DDC |
Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
HDCP |
Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards |
HPD |
Supports hot plug detection (HPD) of display as a pass-through signal. |
Maximum data rate |
6.75 Gbps (2.25 Gbps per color) |
Maximum pixel clock |
225 MHz |
Standards |
DVI 1.0, HDMI 1.3 |
|
Video input — DCX HDMI input boards |
Number/signal type |
4 digital RGB single-link HDMI (or DVI-D*) per input board |
Connectors |
4 female HDMI type A per input board |
Equalization |
Automatic |
Input cable length |
>50' (15.24 m) at 1920x1200 @ 48, 50, or 60 Hz; or 1080p |
NOTE |
The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. | |
|
Video output — DCX HDMI output boards |
Number/signal type |
4 digital RGB single-link HDMI (or DVI-D*) per output board |
Connectors |
4 female HDMI type A per output board |
Re-clocking |
Automatic |
Peripheral device power |
250 mA per output |
|
Control/remote — switcher host ports |
Serial host control port |
1 bidirectional RS-232 or RS-422, rear panel 9-pin female D connector |
Baud rate and protocol |
9600 (default), 19200, 38400, 115200 baud, adjustable; 8 data bits, 1 stop bit, no parity |
Serial control pin configurations |
9-pin female D connector |
|
RS-232 |
2 = Tx, 3 = Rx, 5 = GND |
RS-422 |
2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ |
USB control ports |
1 front panel female mini USB B |
USB standards |
USB 2.0, low speed |
Ethernet control port |
1 RJ-45 female |
Ethernet data rate (for network communication) |
10/100Base-T, half/full duplex with autodetect |
Ethernet protocol |
ARP, ICMP (ping), IP, TCP, DHCP, HTTP, SMTP, Telnet |
Ethernet default settings |
Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.0.0 Default gateway = 0.0.0.0 DHCP = off |
Web server |
Up to 200 simultaneous sessions 7.0 MB nonvolatile user memory |
Program control |
Extron control/configuration program for Windows¢ç Extron Simple Instruction Set¢â (SIS¢â) Microsoft¢ç Internet Explorer¢ç ver. 6 or higher, Telnet |
|
General |
Power |
100 VAC to 240 VAC, 50-60 Hz, 180 watts, internal |
Temperature/humidity |
Storage: -40 to +158 ¡ÆF (-40 to +70 ¡ÆC) / 10% to 90%, noncondensing Operating: +32 to +122 ¡ÆF (0 to +50 ¡ÆC) / 10% to 90%, noncondensing |
Cooling |
Fan, left to right (as viewed from front panel) |
Mounting |
|
Rack mount |
Yes |
Enclosure type |
Metal |
Enclosure dimensions |
7.0" H x 17.0" W x 12" D (4U high, full rack wide) (17.8 cm H x 43.2 cm W x 30.5 cm D) (Depth excludes connectors. Width excludes rack ears.) |
Product weight with boards installed |
18.1 lbs (8.2 kg) |
Shipping weight with boards installed |
22 lbs (10 kg) |
DIM weight, international |
25 lbs (12 kg) |
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
MTBF |
30,000 hours |
Warranty |
3 years parts and labor |